Magnetic Stirrer RRC LKTC-B1-T

Magnetic Stirrer RRC LKTC-B1-T

Features:-



The stainless steel stirring rod of this overhead magnetic stirrer can stand up to

years of use without corrosion or rust, helping to achieve the most accurate mixing

results even for very challenging applications.

- Made of high quality steel, the powerful motor of this electric stirrer can maintain

a long longevity and drive the mixer at the speed of 0~2400 rpm, ideal for any

demanding overhead stirring task in which the viscosity varies during the entire

process either through reaction or due to mixing.

- A smart timer provides additional security and precise operation, an essential

tool for petroleum, chemical, medical, environmental, biochemical laboratory,

analysis room and education department.
    

Package includes:-
1 x the whole machine
- 1 x magnetic beads
- 1 x instruction
- 1 x power line
- 1 x alloys pole
- 1 x alloys ten byte
- 1 x rubber chuck
    
Operation steps:1.
Check if all the necessary accessories are complete,and install them as the

picture shows
2. Put the container(beaker,flask...) onto the center of round plate,add

liquid/solution into the container and put the stirring bar into it
3. Plug in the power cord,turn on the power button,indicator light will be on
4. Choose/set the proper heating temperature you need
5. Turn the rotary knob marked with “Speed adjust” to adjust stirring speed;please

adjust speed from lower to higher(Starting with high speed is not allowed,thus

avoid stirring bar jumping at random)
6. Machine start to work
    
How to adjust the parameters:1.
Long press “SET” for 3 seconds to enter parameter adjustment mode. “Sc”

means the error value between estimated value and real error value, default “Sc”

value is 0.0.
   To adjust the error values, you can press SET again and adjust the error values

between -9.9~9.0
2. Press the button “SET” to enter the adjustment of the next parameter after

finishing the installation. The interphase shows “F” which expresses the lead of

breakpoint control (only come into effect when the value “P” is set up at 0).
   The windows default is 0.5 and the adjustment mode is the same as Sc
3. Again, press the button “SET”to get into the third parameter. “P” on the

interphase is installed with the value “P”, whose meaning is starting control

temperature roughly equals set value (10/p value). If installed at 50 degrees, the

value P starts controlling at 10, showing 49 degrees, while starting adjustment at 4,

showing 47.5 degrees.
   If the temperature is a little higher than it is used, turn down the value “P” properly.

If the temperature is rising slowly, or always not reaching the controlled

temperature, turn up the value “P” in an appropriate way. (Notes: when the value

“P” is zero, which means that it has entered the controlling mode of breakpoint,

that is, the system “PID” is invalid.When the temperature lowers the set value---the

value”E”, it needs heating, otherwise, stop heating.)
4. Again, press the button “SET” and enter the last parameter “C”, which is

temporarily considered as the retention parameter in the inner system. There is no

need for adjustment at this time. The windows default is 20.0. After all parameters

are set up, press the button “SET” and then go back to the normal working state.

- This magnetic heating stirrer features with high quality DC motor,low noise,

smooth speed.
- And, fully enclosed heating tray is able to be used for auxiliary heating.
- Also, it can set and display temperature for accurate intuition. Made from PTFE

and the high quality magnetic steel, this stirred features with high temperature

resistance, abrasion resistance, chemical corrosion resistance, strong magnetic.
- What’s more, it is extremely convenient for you to do mixing work in airtight

contain

- This equipment is widely used in large and medium-sized institutions,

environmental protection, scientific research, sanitation, immunization, oil,

metallurgical, chemical, medical and other units.
- Supply voltage: 110V ± 10% 50HZ
- Motor Power: 25W
- Hot-wire power: 300W
- Magnetic speed: Up to 2400 r/min
- Dimensions: 10.6 x 8.3 x 7.9 inches
- Weight : 5.25 pounds

Untuk informasi lebih lanjut dan ketersediaan stok, silakan hubungi :
CV. DIAN MEDICA
up : Frans Prasetyo
HP/WA : 0895329600425